APPLICATIONS OF THE MOC3011 TRIAC DRIVER DOWNLOAD

Power supply designers have, most often, overcome this problem by More information. Built-in zero-cross S1D, S1D. In practice, this would be a or ohm resistor. Built-in element to absorb a surge current derived from changing motor direction More information. In order to design a snubber properly, one should really know the power factor of the reactive load, which is defined as the cosine of the phase shift caused by the load.

Uploader: Zukasa
Date Added: 22 April 2013
File Size: 69.58 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 45417
Price: Free* [*Free Regsitration Required]

Application Note AN-3003 Applications of Non Zero Crossing Triac Drivers Featuring the MOC3011

In this case, it is possible the MOC and the associated triac will be triggered on. It has been optimized for. The LED is guaranteed by the speci? For example the requires at least 10mA of LED current to guarantee turn-on.

Application Notes: TRIAC Driver Optocouplers

By itself, it will supply output currents up to ma. This technique extends the life of incandescent lamps and reduces EMI generated by load switching. When the designer has more control of the input and output conditions, he can eliminate those components which are needed off his particular application to make the circuit mof3011 cost effective.

In practice, this would be a or ohm resistor. The is used to help protect sensitive digital or analog input circuits on data, More information. In order to design a snubber properly, one should really know the power factor of the reactive load, which is defined as the cosine of the phase shift caused by the load.

See Also  ASUS AR8151 DRIVER DOWNLOAD

A standard value, ohm resistor can be used in practice for R1. To reduce system disturbances it is hte essential. To reduce system disturbances it is therefore essential More information.

Application Notes

In many applications the snubber used for the MOC will also adequately protect the triac. CMOS, for example, is speci?

Such wiring usually is not required to be put in conduit, so the cost savings in installing a lighting system in commercial or residential buildings can be considerable. In some cases, this may require two snubbers-one for the triac and one for the. This technique extends the life of incandescent lamps and reduces EMI generated by load switching.

The detector has a minimum blocking voltage of 50 Vdc in either direction in the off state.

Ordering Information Description The SX is a bi-directional, single-pole, single-throw, normally open multipurpose solid-state relay. Increasing apllications for numerical control machines, robotics and technically advanced appliances More information.

A 4-bit address code determines More information. Remote Control of ac Voltage Local building codes frequently require all light switch wiring to be enclosed in conduit.

The LED is guaranteed by the specifications to trigger the detector into the on state when the current passing through the LED is equal to, or greater than the I FT max specification. When used this way, two resistors are required to equalize the voltage dropped across them as shown in Figure 7.

Life support devices or systems are devices or systems which, appications are intended for surgical implant into the body, or b support or sustain life, or c whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to appplications in significant injury to the user. It has the same pin-out as.

See Also  INCA AMX-CA80U WINDOWS 7 DRIVER

Maximum 30W output power Silvertel V1. Increasing demands for numerical control machines, robotics and technically advanced appliances.

If the triac is to be triggered when Vin 0V: Safety, policy and warranty. Power supply designers have, most often, overcome this problem by. Ordering Information Description Features The SX is a bi-directional, single-pole, single-throw, normally open multipurpose solid-state relay.

Application Note AN Applications of Non Zero Crossing Triac Drivers Featuring the MOC PDF

A Constant-current Source A Constant-current Source Frequently, such as when you want to measure temperature with a silicon diode, it is desirable to have a source of a reproducible, constant current. Once triggered into the on conducting state, the detector will remain there until the current drops below the holding current typically ?

F, the snubbing requirements are met. Applications Examples Using the on 0 Vac Lines The rated voltage of a is not sufficiently high for it to be used directly on 0 Vac line; however, the designer may attach two of them in series.